www3003.com(中国)有限公司-首页

服务热线: 400-117-8816
           13406879330

扭剪螺栓专用扳手,扭剪扳手,扭剪电动扳手,扭剪型电动扳手,扭剪枪的研发与生产

当前位置:首页>技术文献扭剪型电动扳手操作时要注意什么?

扭剪型电动扳手操作时要注意什么?

来源: 日期:2023-03-30 发布人:admin

扭剪型电动扳手

Torsional shear type electric wrench
是拆卸指纹件及螺帽的机器化施工机器,存正在主动掌握扭矩性能。扭剪扳手宽泛使用于栓焊构造桥梁的架构,厂房塔架及化工冶金火力发电设施的装置。重型机器起重设施和车辆拆卸工作,以及对于螺纹紧固件的扭矩及轴向张力有严厉要求的场所。接下来我们来看看扭剪扳手的操作注意事项:
It is a mechanized construction machine that disassembles fingerprint parts and nuts, and actively grasps torque performance. Torsion wrenches are widely used in the construction of bolted and welded bridge structures, plant towers, and chemical, metallurgical, thermal power generation facilities. Heavy machine lifting facilities and vehicle disassembly work, as well as places with strict requirements for torque and axial tension of threaded fasteners. Next, let's take a look at the precautions for operating a torsion wrench:
扭剪型电动扳手
Torsional shear type electric wrench
接回电源前应先检查电源电压能否与本货物铭牌符合,能否有接地安装。当电源电压超过+10%时应采取稳压措施,要不会反应掌握精密度。接地没有良易形成事变。
Before connecting back to the power supply, check whether the power supply voltage conforms to the nameplate of the goods and whether there is a grounding installation. When the power supply voltage exceeds+10%, voltage stabilization measures should be taken to ensure accuracy. Grounding is not conducive to accidents.
机器运用的条件量度为-10℃-40℃,过高过低都会反应掌握精密度。
扭剪扳手
 
The condition measurement for machine operation is - 10 ℃ - 40 ℃. Too high or too low will reflect the mastery of precision.
机器用来组装螺帽时,其扭矩没有得大于额外扭矩值。正常状况下,没有是本拉手拧紧的或者锈蚀重大的螺帽,没有宜用本拉手组装,免得形成机器保护。
When the machine is used to assemble nuts, the torque is not greater than the additional torque value. Under normal conditions, there are no nuts tightened or heavily rusted by this handle, and no nuts should be assembled using this handle to avoid forming machine protection.
变换旋转位置时,必需待发电机中止转动后停止,严禁正在运行中扳动正反电门。
When changing the rotating position, it is necessary to wait until the generator stops rotating. It is strictly prohibited to pull the forward and reverse switches during operation.
当拉手主动中止后即可抓紧电门待4-5秒后再停止开行拉手,要不拉手不能发动。
When the handle is actively stopped, you can grab the switch and wait 4-5 seconds before stopping the handle, otherwise the handle cannot be started.

Baidu
sogou